NP263 Chevrolet & GMC Transfer Case Buy Factory Direct & Save, we Ship World Wide!

See the complete line of products that we can provide at www.midwesttrans.. To speak to a Drive Train Expert or to place and order call toll free 888-824-2012, buy factory direct and save money!

Having issues diagnosing problems with your NP263 transfer case? We can help free knowledgeable technical support! We have a large inventory of rebuilt NP263 transfer cases plus Transfer Case parts. Our factory rebuilt re-manufactured

np263 transfer case replacements and parts
Brand New NV263HD MWTTCGM038 your cost $1500.00 plus $500.00 core deposit plus freight, while they last. Call toll free at 888-824-2012. Save Money no hassle 12 month warranty! .

replacement NP263 rear caseTransfer Cases are tested before leaving the factory. This transfer case was manufactured by New Process. This model is a chain driven electric shift and part time transfer case. The output is on the driver-side with center rear output. This unit has been utilized in Chevrolet and GMC 1500, 2500 and 3500 pickup trucks & Suburbans from 2001-Up. There are three different versions of this unit the light duty "LD" , heavy duty "HD" and the extra heavy duty unit "XHD". The 263XHD unit is supplied with most diesel versions, the HD version has a 6 pinion planet and utilizes a 1.5" wide chain.

The NP263 has 2.72:1 ratio, and has a magnesium case has either 4WD full-time, neutral and low 4WD, 2WD high and 4WD high. These units have different input spline counts: 27 splines in the NP263, 32 splines in the NP263 and 29 input splines in the NP263XHD.

This unit has a couple of engineering design problems, the oil pump can wear a hole in the rear case half, we recommend as part of your preventative maintenance program to install our machined aluminum case protector to save major repairs. A better option may be to install an upgraded rear case, see above. The second problem is thought to be caused by heat build up, failure of the shift forks causing the plastic pads to melt and damage the range shift hub and sometimes cause shaft damage. Recommended fluid is Automatic Transmission Fluid ATF.

We can provide a rebuilt NP263 transfer cases with a 12 month warranty we also offer all parts required to rebuild your unit, we have new parts we can also provide good used takeout parts to save you money!

Select this link to see what models that use this Transfer Case.

Free NP263 Transfer Case parts illustration

Below we provide a NP263 parts illustrations to assist you with the correct identification of the parts you need. Select the parts you require from the the list below and give us a call.

Below you will find a detailed list that includes complete rebuilt Transfer Cases, bearing rebuild kits, gaskets, seals, small parts & thrust washers, bushings individual bearing, forks, hub sliders, synchronizers, shift motor, oil pump, planets, shafts, cases_housings, chain, sprockets and miscellaneous parts. If you need more information or cannot find the parts you need give us a call, if you would like to save money, ask about our good take out parts (GTO), they are inspected and guaranteed.

Applications Model Years  

np 263 transfer case parts

This information tag is located on rear of transfer case near where the driveshaft exits. The NP263 can be followed by and "HD" or "XHD"

Chevrolet & GMC 2500 263HD 32 spline input 32 spline output 2003-2004
Chevrolet & GMC 2500 263XHD 29 spline input 31 spline output 2003-2004
Chevrolet & GMC 2500 263HD 32 spline input 32 spline output 2003-2007
Chevrolet & GMC 2500 263XHD 29 spline input 31 spline output 2003-2007
Chevrolet & GMC 3500 263HD 32 spline input 32 spline output 2003-2006
Chevrolet & GMC 2500 263XHD 29 spline input 31 spline output 2003-2006
Chevrolet & GMC 3500 263HD 32 spline input 32 spline output 2001-2002
Chevrolet & GMC 2500 263XHD 29 spline input 31 spline output 2001-2002

Need Stronger Parts?

Midwest Transmission can Cryogenic Treat any shaft or gear. This cryo treatment will add 30% in component strength. Call 888-824-2012 for a quote.

Rebuilt Tested NP263 Transfer Cases 12 month warranty

DESCRIPTION ITEM #
YOUR COST
GM Silverado 27 Spline Input 2001-Up NP263 HD MWTTCGM037
$1,326.67
GM Silverado 32 Spline Input 2001-Up NP263 HD MWTTCGM038
$1,326.67
GM Silverado 29 Spline Input 2001-Up NP263 HD MWTTCGM042
$1,326.67
GM Silverado 2500 HD 29 Spline Input, 31 spline rear slip 2001-Up NP263XHD Elec Shift MWTTCGM049
$1,600.00
Core charge on above transfer cases
$500.00

 

Rebuilt Overhaul Bearing Kits & Case Saver NP263 Transfer Case

DESCRIPTION ITEM #
YOUR COST
Bearing Rebuild Kit NP 263 (32 Spline Output) BK371
$130.00
Bearing Rebuild Kit NP 263XHD (31 Spline Output) BK371A
$184.94
SMALL PARTS KITS
Small Parts NP 263 MWTSP263-50
$20.99
Case Saver Unit HD Machined Aluminum MWT52007
$65.00

 

Small Parts Gaskets Seals, Orings & Filter NP263 Transfer Case

DWG # DESCRIPTION ITEM #
YOUR COST
N.I. NP 263 Gasket & Seal Kit TSK261
$39.99
N.I. NP 263XHD Gasket & Seal Kit TSK261XHD
$55.95
SEALS
070A Input Seal 411070
$3.93
081A Front Output Seal. OE MWTGM12547656
$15.00
074A Rear Output Seal (2.695 inch x 1.825 inch) OE MWTNV21938
$12.50
074A Rear Output Seal (3.035 inch x 2.125 inch) OE MWTNV22507
$25.00S
FILTERS
012E Pump Screen (38 Spline Pump) (NP 263) 351012
$4.94
012E Pump Screen (49 Spline Pump) (NP 263, NP 263XHD) 351012-1
$7.97
012-1 Hose, Filter to Tube (NP 263XHD) 435012
$12.92
GASKETS & O-RINGS
330A O-Ring, Detent (All) 401330
$0.05
330A O-Ring, Indicator Switch (All) 401330
$0.05
330A O-Ring, Pump Pick-Up Tube (38 Spline Pump) (NP 263) 401330
$0.05
330A O-Ring, Pump Pick-Up Tube (49 Spline Pump) (NP 263, NP 263XHD) 401330A
$0.07
  Small Parts Kit    
  Small Parts Kit MWTSP263.-50
$35.00

 

Bushings & Washers NP263 Transfer Case

DWG # DESCRIPTION ITEM #
YOUR COST
066A Extension Housing (2.010” OD) (NP 263) MWT100408
$10.00
066A Extension Housing (2.340” OD) (NP 263XHD) MWTNV18172
$15.00
WASHERS
215C Planet Thrust Washer (Plastic) MWTNP4338908
$4.00

 

Bearings NP263 Transfer Case

DWG # DESCRIPTION ITEM #
YOUR COST
210D Output Bearing (Rear) (NP 263) 342210
$11.91
  Output Bearing (Rear) (NP 263XHD) MWTB41-6
$45.00

 

Shift Forks NP263 Transfer Case

DWG # DESCRIPTION ITEM #
YOUR COST
850B Mode Fork (Aluminum) (Cast # 28624) (All). MWTNV27756
$68.98
849B Range Fork (Fits Slider w/ .368” Wide Fork Groove) (All) 401849
$41.91
849B Range Fork (NP 263XHD) no pads MWTNV43682
$139.99
840KB Fork Insert Kit (All) 401840K
$16.96

 

Shift Hubs & Sliders NP263 Transfer Case

DWG # DESCRIPTION ITEM #
YOUR COST
646C Mode Slider (NP 263, NP 263XHD) 401646
$54.94
645C Range Slider & Hub (Updated) (.368” Wide Fork Groove) (NP 263) MWtNP4796906
$67.97
645C Range Slider & Hub (NP 263XHD) MWTNV43681
$65.00
606D Drive Hub / Bushing (Splines into Drive Sprocket) (1 Piece Synchro). 401606A
$146.96
606D Drive Hub / Bushing (Splines into Drive Sprocket) (2 Piece Synchro). 401606
$48.98

 

Synchronizers NP263 Transfer Case

DWG # DESCRIPTION ITEM #
YOUR COST
701-1D Mode Synchro (Inner) (All) 401701-1
$33.93
701-3D Mode Synchro (Middle) Friction (All) 401701-3
$42.92
701-5D Mode Synchro (Outer) (All) 401701-5
$50.90
843-2KC Mode Key & Spring Kit (All) 331843-2K
$12.92

 

Pump & Planet NP263 Transfer Case

DWG # DESCRIPTION ITEM #
YOUR COST
PUMPS
500D Pump Assembly (38 Spline) (NP 263) 371500
$42.92
500D Pump Assembly (49 Spline) (NP 263, NP 263XHD) MWTNV25904
$65.00
463E Tube, Oil Pump (38 Spline Pump) (NP 263). 482463
Call
463E Tube, Oil Pump (49 Spline Pump) (NP 263XHD) 482463A
$5.95
PLANETS
588C Planet (6 Pinion) (used w/ .630” Wide Input Bearing) 351588A
$178.98

 

Shafts NP263 Transfer Case

DWG # DESCRIPTION ITEM #
YOUR COST
670C Input Shaft (27 Spline) (NP 263) 401670
$123.93
670C Input Shaft (32 Spline) (NP 263) MWTNV42740
$193.75
670C Input Shaft (29 Spline) (NP 263XHD) MWTNV43966
$145.00
672D Main Shaft (38 Spline Pump) (NP 263) 401672
$173.93
672D Main Shaft (49 Spline Pump) (NP 263HD) MWTNV48714
$199.89
672D Main Shaft (49 Spline Pump) (NP 263XHD). MWTNV47936
$168.98

 

Cases & Housings NP263 Transfer Case

DWG # DESCRIPTION ITEM #
YOUR COST
760-1A Case Half (Front) (NP 263HD) NV29231 MWT45544
760-1A Case Half (Front) (NP 263) 401760C-1
$450.90
760-1A Case Half (Front) (NP 263XHD) MWTNV45545
$381.00
760-2A Case Half (Rear) (NP 263 Standard) MWTNV30961
$175.00
760-2A Case Half (Rear) (NP 263 XDH) (Cast # 25909) MWTNV25900
$180.00

 

Chain & Sprocket NP263 Transfer Case 

DWG # DESCRIPTION ITEM #
YOUR COST
700E Chain (1.25” Wide) 49 Links, 3 Blue Links CL10-072
$91.89
700E Chain (1.50” Wide) 42 Links XHD CL10-074
$144.40
700E Chain (1.50” Wide) 49 Links XHD CL-069
$108.98
805D Drive Sprocket (1.25” Chain) (NP 263). 401805
$33.65
805D Drive Sprocket (1.50” Chain) (NP 263). 401805B
$53.93
805D Drive Sprocket (1.50” Chain) (NP 263XHD). 401805A
$40.90
806E Driven Sprocket (1.25” Chain) (NP 263) 401805
$33.65
806E Driven Sprocket (1.50” Chain) (NP 263) 401805B
$53.93
806E Driven Sprocket (1.50” Chain) (NP 263XHD) 401805A
$40.90

 

Miscellaneous Components NP263 Transfer Case 

DWG # DESCRIPTION ITEM #
YOUR COST
N.I. Selector Support, Shift Cam (All) 401626A
$30.90
420A Shift Motor (01-Up) MWTUMM2263
$231.91
Core on above shift motor
$50.00
862D Snap Ring, Drive Hub (All) 16205
$1.60
861D Snap Ring, Rear Output Shaft Bearing (NP 263). 352860C
$17.97
861D Snap Ring, Rear Output Shaft Bearing (NP 263XHD) 352860B
$3.93
860D Snap Ring, Rear Main Shaft Bearing, Outer (All). 482860
$2.92
436A Speed Sensor (All) 411436
$29.99
997D Speedometer Tone Wheel (38 Spline) (NP 263) 401997
$37.97
997D Speedometer Tone Wheel (49 Spline) (NP 263, NP 263XHD) 401997A
$11.91
775A Stud, Front Case (All) 492775
$2.92
490A Vent Tube (All) 411490
$3.93
Click Images to enlarge and shrink

np263 transfer case replacement and partsnp263 transfer case replacement and parts

 

case saver   shift motor np263
encoder shift motor np263    

 

Minimum order $25.00, Shipping and handling charges will be added.

 

ax15 parts